WHEEL LOADER LKP – 0301 ENG
WHEEL LOADER LKP – 0301
Destination
Wheel loader LKP-0301 (bucket loader) is destined to work for loading and transportin winning from active end to reload point in unmethane excavation mineral raw mines. Except operating ore from active end and loading to dumping car, relative to flat point unloading ore this wheel loader can be use to auxiliary work for example : equalization, cleanin excavations, scraping of winning in active end etc.Good stability of wheel loader assure drive, during drive straight as well as duringturning (in whole range turning angle) in direction of carriage and in direction of bucket in excavations about inclination in drive direction to 11° and in perpendicular direction to 4°.Because of good manoeuvrability of loader (turning system make possible turn about 42° in both sides), it can be drive free in gallery crossing under angle 90° (inner turning radius Rw =2560 mm, outer turning radius Rw = 4690 mm). Big (total) pressure force (break out force 74kN, pull force 70kN, tramming capacity 3,2 t) assure good loading the bucket (bucketcapacity 1,6 m3, max. depth loosening of rock 690 mm). Working unit allow for unloading in galleries about height 3860 mm (max. unloading height 1635 mm by unloading angle 44°).Max. driving speed: front/rear = 19,0 km/h
Specification
| Engine | DEUTZ F6L912W |
| Diesel, 6-cyliders, four-stroke, air-cooled | |
| Power rating | 60 kW at 2300 rpm |
| Torque | 275 Nm at 1400 rpm |
| Induction system |
air filter GF-7.60.00 with below atmospheric sensor of pollution |
| Exhaust system | catalyst SZOP 07 + washer |
| Transmission | CLARK R28362 |
| Torque converter | CLARK C-271 |
| Turn system | REXROTH
|
| Driving axle – front/rear | 479-22-0000 (FON RADOMSKO) |
| Braking system | hydraulic REXROTH |
| Service brake | multidisks "wet" |
| Emergency-parking brake | HAP |
| Tyres | 14,0x24 - tube |
| Bucket |
standard 1,6m3 - steel 18G2A+ working equip. steel HARDOX 500 |
| Lubrication | manual point |
| Electrical installation | 24 V |
Dimensions and technical data
| Length | |
| Bucket rest on the ground | 7 850 mm |
| Bucket in transport position | 7 540 мм
|
| Width | |
| Over tyres | 1 600 мм |
| Over bucket | 1 760 мм |
| Height | 2 100 мм |
| Operating weight | 10 800 кг |
| Operating weight | 10 800 kg |
| Disposition of operating weight (without loading): | |
| For front axle | 4 840 кг |
| For rear axle | 5 960 кг |
| Nominal bucket capacity | 1,6 м3 |
| Tramming capacity | 32 kN |
| Break out force on bucket edge | 74 kN |
| Pull force | 70 kN |
| Max. unloading height 1635 mm by unloading angle 44° | 1 635 mm |
| Range unloading by unloading angle 44° | 1 360 mm |
| Max. depth of loosening of rock | 690 mm |
| Max. depth of loosening of rock | 690 mm |
| Max. angle unloading bucket | 44° |
| Max. angle loading bucket | 42° |
| Hill climbing ability | 97% |
| Angle of tilt rear axle | ± 10° |
| Hill climbing angle | 11° |
| Clearance | 260 мм |
| Inner turning radius | 2 560 мм |
| Outer turning radius | 4 690 мм
|
| Max. speed (forward and reverse) | |
| I gear | 0^4,5 |
| II gear | 0^9,0 |
| III gear | 0^19,0 |
| Pressure in tyres | |
| Front | 0,5 MPa
|
| Rear | 0,4 Mpa |
| Working times: | |
| Lifting boom | 5,5±10%с |
| Lowing boom | 4,5±10%с |
| Opening bucket | 2,5±10%с |
| Closing bucket | 3,0±10%с |
| Full turn | 3,0±10%с |
Назад в раздел